spec/spec_helper.rb in enju_leaf-1.1.0.rc20 vs spec/spec_helper.rb in enju_leaf-1.1.0.rc21

@@ -1,57 +1,92 @@
-require 'simplecov'
-require 'coveralls'
-SimpleCov.start 'rails'
-Coveralls.wear!
-
-require 'capybara/rspec'
-require 'cancan/matchers'
-
-# This file is copied to spec/ when you run 'rails generate rspec:install'
-ENV["RAILS_ENV"] ||= 'test'
-require File.expand_path("../dummy/config/environment", __FILE__)
-require 'rspec/rails'
-require 'vcr'
-require 'factory_girl'
-require 'sunspot-rails-tester'
-require 'rspec/active_model/mocks'
-
-# Requires supporting ruby files with custom matchers and macros, etc,
-# in spec/support/ and its subdirectories.
-Dir["#{File.dirname(__FILE__)}/support/**/*.rb"].each { |f| require f }
-
+# This file was generated by the `rails generate rspec:install` command. Conventionally, all
+# specs live under a `spec` directory, which RSpec adds to the `$LOAD_PATH`.
+# The generated `.rspec` file contains `--require spec_helper` which will cause
+# this file to always be loaded, without a need to explicitly require it in any
+# files.
+#
+# Given that it is always loaded, you are encouraged to keep this file as
+# light-weight as possible. Requiring heavyweight dependencies from this file
+# will add to the boot time of your test suite on EVERY test run, even for an
+# individual file that may not need all of that loaded. Instead, consider making
+# a separate helper file that requires the additional dependencies and performs
+# the additional setup, and require it from the spec files that actually need
+# it.
+#
+# The `.rspec` file also contains a few flags that are not defaults but that
+# users commonly want.
+#
+# See http://rubydoc.info/gems/rspec-core/RSpec/Core/Configuration
 RSpec.configure do |config|
-  # == Mock Framework
-  #
-  # If you prefer to use mocha, flexmock or RR, uncomment the appropriate line:
-  #
-  # config.mock_with :mocha
-  # config.mock_with :flexmock
-  # config.mock_with :rr
-  config.mock_with :rspec
+  # rspec-expectations config goes here. You can use an alternate
+  # assertion/expectation library such as wrong or the stdlib/minitest
+  # assertions if you prefer.
+  config.expect_with :rspec do |expectations|
+    # This option will default to `true` in RSpec 4. It makes the `description`
+    # and `failure_message` of custom matchers include text for helper methods
+    # defined using `chain`, e.g.:
+    #     be_bigger_than(2).and_smaller_than(4).description
+    #     # => "be bigger than 2 and smaller than 4"
+    # ...rather than:
+    #     # => "be bigger than 2"
+    expectations.include_chain_clauses_in_custom_matcher_descriptions = true
+  end
 
-  # Remove this line if you're not using ActiveRecord or ActiveRecord fixtures
-  config.fixture_path = "#{::Rails.root}/../../spec/fixtures"
+  # rspec-mocks config goes here. You can use an alternate test double
+  # library (such as bogus or mocha) by changing the `mock_with` option here.
+  config.mock_with :rspec do |mocks|
+    # Prevents you from mocking or stubbing a method that does not exist on
+    # a real object. This is generally recommended, and will default to
+    # `true` in RSpec 4.
+    mocks.verify_partial_doubles = true
+  end
 
-  # If you're not using ActiveRecord, or you'd prefer not to run each of your
-  # examples within a transaction, remove the following line or assign false
-  # instead of true.
-  config.use_transactional_fixtures = true
-  config.extend ControllerMacros, :type => :controller
+# The settings below are suggested to provide a good initial experience
+# with RSpec, but feel free to customize to your heart's content.
+=begin
+  # These two settings work together to allow you to limit a spec run
+  # to individual examples or groups you care about by tagging them with
+  # `:focus` metadata. When nothing is tagged with `:focus`, all examples
+  # get run.
+  config.filter_run :focus
+  config.run_all_when_everything_filtered = true
 
-  $original_sunspot_session = Sunspot.session
+  # Allows RSpec to persist some state between runs in order to support
+  # the `--only-failures` and `--next-failure` CLI options. We recommend
+  # you configure your source control system to ignore this file.
+  config.example_status_persistence_file_path = "spec/examples.txt"
 
-  config.before do
-    Sunspot.session = Sunspot::Rails::StubSessionProxy.new($original_sunspot_session)
-  end
+  # Limits the available syntax to the non-monkey patched syntax that is
+  # recommended. For more details, see:
+  #   - http://myronmars.to/n/dev-blog/2012/06/rspecs-new-expectation-syntax
+  #   - http://www.teaisaweso.me/blog/2013/05/27/rspecs-new-message-expectation-syntax/
+  #   - http://myronmars.to/n/dev-blog/2014/05/notable-changes-in-rspec-3#new__config_option_to_disable_rspeccore_monkey_patching
+  config.disable_monkey_patching!
 
-  config.before :each, :solr => true do
-    Sunspot::Rails::Tester.start_original_sunspot_session
-    Sunspot.session = $original_sunspot_session
-    Sunspot.remove_all!
+  # Many RSpec users commonly either run the entire suite or an individual
+  # file, and it's useful to allow more verbose output when running an
+  # individual spec file.
+  if config.files_to_run.one?
+    # Use the documentation formatter for detailed output,
+    # unless a formatter has already been configured
+    # (e.g. via a command-line flag).
+    config.default_formatter = 'doc'
   end
 
-  config.infer_spec_type_from_file_location!
-end
+  # Print the 10 slowest examples and example groups at the
+  # end of the spec run, to help surface which specs are running
+  # particularly slow.
+  config.profile_examples = 10
 
-FactoryGirl.definition_file_paths << "#{::Rails.root}/../../spec/factories"
-FactoryGirl.find_definitions
+  # Run specs in random order to surface order dependencies. If you find an
+  # order dependency and want to debug it, you can fix the order by providing
+  # the seed, which is printed after each run.
+  #     --seed 1234
+  config.order = :random
+
+  # Seed global randomization in this process using the `--seed` CLI option.
+  # Setting this allows you to use `--seed` to deterministically reproduce
+  # test failures related to randomization by passing the same `--seed` value
+  # as the one that triggered the failure.
+  Kernel.srand config.seed
+=end
+end