| Top | |
|
|
|
| gboolean | album-mode | Read / Write |
| gdouble | fallback-gain | Read / Write |
| gdouble | headroom | Read / Write |
| gdouble | pre-amp | Read / Write |
| gdouble | result-gain | Read |
| gdouble | target-gain | Read |
GObject ╰── GInitiallyUnowned ╰── GstObject ╰── GstElement ╰── GstBin ╰── GstRgVolume
This element applies volume changes to streams as lined out in the proposed
ReplayGain standard. Itinterprets the ReplayGain meta data tags and carries out the adjustment (by using a volume element internally). The relevant tags are:
The information carried by these tags must have been calculated beforehand by performing the ReplayGain analysis. This is implemented by the rganalysis element.
The signal compression/limiting recommendations outlined in the proposed standard are not implemented by this element. This has to be handled by separate elements because applications might want to have additional filters between the volume adjustment and the limiting stage. A basic limiter is included with this plugin: The rglimiter element applies -6 dB hard limiting as mentioned in the ReplayGain standard.
1 2 |
gst-launch-1.0 filesrc location=filename.ext ! decodebin ! audioconvert \ ! rgvolume ! audioconvert ! audioresample ! alsasink |
plugin |
replaygain |
author |
René Stadler <mail@renestadler.de> |
class |
Filter/Effect/Audio |
name |
sink |
direction |
sink |
presence |
always |
details |
audio/x-raw, format=(string){ F32LE, S16LE }, layout=(string){ interleaved, non-interleaved }, rate=(int)[ 1, 2147483647 ], channels=(int)[ 1, 2147483647 ] |
name |
src |
direction |
source |
presence |
always |
details |
audio/x-raw, format=(string){ F32LE, S16LE }, layout=(string){ interleaved, non-interleaved }, rate=(int)[ 1, 2147483647 ], channels=(int)[ 1, 2147483647 ] |
“album-mode” property“album-mode” gboolean
Whether to prefer album gain over track gain.
If set to TRUE, use album gain instead of track gain if both are
available. This keeps the relative loudness levels of tracks from the same
album intact.
If set to FALSE, track mode is used instead. This effectively leads to
more extensive normalization.
If album mode is enabled but the album gain tag is absent in the stream, the track gain is used instead. If both gain tags are missing, the value of the “fallback-gain” property is used instead.
Flags: Read / Write
Default value: TRUE
“fallback-gain” property“fallback-gain” gdouble
Fallback gain [dB] for streams missing ReplayGain tags.
Flags: Read / Write
Allowed values: [-60,60]
Default value: 0
“headroom” property“headroom” gdouble
Extra headroom [dB]. This controls the amount by which the output can exceed digital full scale.
Only set this to a value greater than 0.0 if signal compression/limiting of a suitable form is applied to the output (or output is brought into the correct range by some other transformation).
This element internally uses a volume element, which also supports operating on integer audio formats. These formats do not allow exceeding digital full scale. If extra headroom is used, make sure that the raw audio data format is floating point (F32). Otherwise, clipping distortion might be introduced as part of the volume adjustment itself.
Flags: Read / Write
Allowed values: [0,60]
Default value: 0
“pre-amp” property“pre-amp” gdouble
Additional gain to apply globally [dB]. This controls the trade-off between uniformity of normalization and utilization of available dynamic range.
Note that the default value is 0 dB because the ReplayGain reference value was adjusted by +6 dB (from 83 to 89 dB). At the time of this writing, the
webpage is still outdated anddoes not reflect this change however. Where the original proposal states that a proper default pre-amp value is +6 dB, this translates to the used 0 dB.
Flags: Read / Write
Allowed values: [-60,60]
Default value: 0
“result-gain” property“result-gain” gdouble
Applied gain [dB]. This gain is applied to processed buffer data.
This is set to the “target-gain” if amplification by that amount can be applied safely. "Safely" means that the volume adjustment does not inflict clipping distortion. Should this not be the case, the result gain is set to an appropriately reduced value (by applying peak normalization). The proposed standard calls this "clipping prevention".
The difference between target and result gain reflects the necessary amount of reduction. Applications can make use of this information to temporarily reduce the “pre-amp” for subsequent streams, as recommended by the ReplayGain standard.
Note that target and result gain differing for a great majority of streams indicates a problem: What happens in this case is that most streams receive peak normalization instead of amplification by the ideal replay gain. To prevent this, the “pre-amp” has to be lowered and/or a limiter has to be used which facilitates the use of “headroom”.
Flags: Read
Allowed values: [-120,120]
Default value: 0
“target-gain” property“target-gain” gdouble
Applicable gain [dB]. This gain is supposed to be applied.
Depending on the value of the “album-mode” property and the presence of ReplayGain tags in the stream, this is set according to one of these simple formulas:
Flags: Read
Allowed values: [-120,120]
Default value: 0