STATE_DISABLED STATE_ENABLED WOC_NAT_SOURCE_ADDRESS_NONE WOC_NAT_SOURCE_ADDRESS_CLIENT WOC_NAT_SOURCE_ADDRESS_WOM WOC_NAT_SOURCE_ADDRESS_TUNNEL MCP_ORIGIN_DISCOVERED MCP_ORIGIN_CONFIGURED MCP_ORIGIN_PERSISTABLE MCP_ORIGIN_MANUALLY_SAVED Gets the names of all remote endpoints. Creates a set of remote endpoints. Deletes a set of remote endpoints. Deletes all remote endpoints. Gets the local endpoint IP address for a set of remote endpoints. Note: A set_address method is not supported. Sets the state to indicate that this is located behind a Network Address Translation device for a set of remote endpoints. Gets the state to indicate that this is located behind a Network Address Translation device for a set of remote endpoints. Gets the total amount of cache available for symmetric data deduplication for a set of remote endpoints. The system apportions this cache according to the number of remote endpoints and the amount of cache available at each endpoint. Sets the description for a set of remote endpoints. This is an arbitrary field which can be used for any purpose. Gets the descriptions for a set of remote endpoints. Sets the management IP address for a set of remote endpoints. Gets the management IP address for a set of remote endpoints. Sets the configuration status for a set of remote endpoints. Gets the configuration status for a set of remote endpoints. Sets the SNAT address source for a set of remote endpoints. Gets the SNAT address source for a set of remote endpoints. Sets the how the remote endpoint was created for a set of remote endpoints. You can change the origin from "discovered" to "persistable", if you want to save the endpoint configuration. After a remote endpoint has been saved, this attribute is changed to "manually saved". Any remote endpoints marked as "discovered" are not saved. Gets the how the remote endpoint was created for a set of remote endpoints. Sets the state to optimize traffic between the local endpoint and this remote endpoint for a set of remote endpoints. Disabling a remote endpoint affects only the connection between the local endpoint and this remote endpoint. Gets the state to optimize traffic between the local endpoint and this remote endpoint for a set of remote endpoints. Gets the list of IP addresses that the local endpoint uses to communicate with the WAN Optimization Module on a remote BIG-IP system for a set of remote endpoints. Gets the host name of the BIG-IP system that hosts this remote endpoint for a set of remote endpoints. Sets the state to indicate that a route exists from the local endpoint to this remote endpoint through which the local endpoint can establish connections for a set of remote endpoints. If not set, the local endpoint cannot initiate traffic to the remote endpoint. Gets the state to indicate that a route exists from the local endpoint to this remote endpoint through which the local endpoint can establish connections for a set of remote endpoints. Sets the sSL profile used for authenticating (encrypting for a set of remote endpoints.) traffic to this remote endpoint. Note that this setting overrides the analogous setting in the local endpoint. Gets the sSL profile used for authenticating (encrypting for a set of remote endpoints. Sets the local endpoint IP service that the WAN Optimization Module uses to control connections for a set of remote endpoints. This must be a service that is allowed access through the firewall. Gets the local endpoint IP service that the WAN Optimization Module uses to control connections for a set of remote endpoints. Gets the universal Unique Identifier, a 128-bit number that identifies this remote endpoint for a set of remote endpoints. Gets the version information for this interface. Gets the names of all remote endpoints. Creates a set of remote endpoints. Deletes a set of remote endpoints. Deletes all remote endpoints. Gets the local endpoint IP address for a set of remote endpoints. Note: A set_address method is not supported. Sets the state to indicate that this is located behind a Network Address Translation device for a set of remote endpoints. Gets the state to indicate that this is located behind a Network Address Translation device for a set of remote endpoints. Gets the total amount of cache available for symmetric data deduplication for a set of remote endpoints. The system apportions this cache according to the number of remote endpoints and the amount of cache available at each endpoint. Sets the description for a set of remote endpoints. This is an arbitrary field which can be used for any purpose. Gets the descriptions for a set of remote endpoints. Sets the management IP address for a set of remote endpoints. Gets the management IP address for a set of remote endpoints. Sets the configuration status for a set of remote endpoints. Gets the configuration status for a set of remote endpoints. Sets the SNAT address source for a set of remote endpoints. Gets the SNAT address source for a set of remote endpoints. Sets the how the remote endpoint was created for a set of remote endpoints. You can change the origin from "discovered" to "persistable", if you want to save the endpoint configuration. After a remote endpoint has been saved, this attribute is changed to "manually saved". Any remote endpoints marked as "discovered" are not saved. Gets the how the remote endpoint was created for a set of remote endpoints. Sets the state to optimize traffic between the local endpoint and this remote endpoint for a set of remote endpoints. Disabling a remote endpoint affects only the connection between the local endpoint and this remote endpoint. Gets the state to optimize traffic between the local endpoint and this remote endpoint for a set of remote endpoints. Gets the list of IP addresses that the local endpoint uses to communicate with the WAN Optimization Module on a remote BIG-IP system for a set of remote endpoints. Gets the host name of the BIG-IP system that hosts this remote endpoint for a set of remote endpoints. Sets the state to indicate that a route exists from the local endpoint to this remote endpoint through which the local endpoint can establish connections for a set of remote endpoints. If not set, the local endpoint cannot initiate traffic to the remote endpoint. Gets the state to indicate that a route exists from the local endpoint to this remote endpoint through which the local endpoint can establish connections for a set of remote endpoints. Sets the sSL profile used for authenticating (encrypting for a set of remote endpoints.) traffic to this remote endpoint. Note that this setting overrides the analogous setting in the local endpoint. Gets the sSL profile used for authenticating (encrypting for a set of remote endpoints. Sets the local endpoint IP service that the WAN Optimization Module uses to control connections for a set of remote endpoints. This must be a service that is allowed access through the firewall. Gets the local endpoint IP service that the WAN Optimization Module uses to control connections for a set of remote endpoints. Gets the universal Unique Identifier, a 128-bit number that identifies this remote endpoint for a set of remote endpoints. Gets the version information for this interface. Remote endpoint for the traffic from the local WAN Optimization Module endpoint. A single local endpoint can work with multiple remote endpoints.