STATE_DISABLED STATE_ENABLED UNIT_UNKNOWN UNIT_BPS UNIT_KBPS UNIT_MBPS UNIT_GBPS Gets the names of all Bandwidth Controller policies.

Creates a set of Bandwidth Controller policies.

Deletes a set of Bandwidth Controller policies.

Deletes all Bandwidth Controller policies.

Sets the descriptions for the specified Bandwidth Controller policies. This is an arbitrary field which can be used for any purpose.

Gets the descriptions for the specified Bandwidth Controller policies.

Gets the dynamic states of the specified Bandwidth Controller policies.

Sets the IP-TOS value for the specified Bandwidth Controller policies. If set then all non-conforming Layer 3 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth policy. A value of 255 means it's a pass through and all the Layer 3 packets are passed as seen by the Bandwidth Controller.

Gets the IP-TOS value for the specified Bandwidth Controller policies.

Sets the Link-QOS for the specified Bandwidth Controller policies. All non-conforming Layer 2 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth policy. A value of 255 means it's a pass through and all the Layer 2 packets are passed as seen by the Bandwidth Controller.

Gets the Link-QOS for the specified Bandwidth Controller policies.

Sets the maximum rate for the specified Bandwidth Controller policies. Maximum rates is maximum bandwidth allowed for all the flows going going through this policy. Maximum rates value should be between 1000000bps and 320000000000 bps.

Gets the maximum rate for the specified Bandwidth Controller policies.

Sets the maximum user rate in packets per second (PPS) for the specified Bandwidth Controller policies. The maximum user rate is the maximum bandwidth allowed for all the flows going through this dynamically created instance of the Bandwidth Controller policy. The maximum user rate cannot be higher than the maximum rate specified for that Bandwidth Controller policy.

Gets the maximum user rate in packets per second (PPS) for the specified Bandwidth Controller policies.

Sets the maximum user rate for the specified Bandwidth Controller policies. Maximum user rates is maximum bandwidth allowed for all the flows going through this dynamically created instance of the Bandwidth Controller policy. Maximum user rate value should be between 5000 bps and 2000000000 bps. Maximum user rate cannot be higher than maximum rate specified for that Bandwidth Controller policy.

Gets the maximum user rate for the specified Bandwidth Controller policies.

Gets the names of all Bandwidth Controller policy categories. Categories is a sub-policy of dynamically created instances from a dynamic enabled policy.

Creates a set of Bandwidth Controller policy categories with the specified maximum rates. Categories is a sub-policy of dynamically created instances from a dynamic enabled policies. Maximum rates cannot exceed the maximum user rate of the parent Bandwidth Controller policy.

Creates a set of Bandwidth Controller policy categories with the specified maximum rate percentages. Categories is a sub-policy of dynamically created instances from a dynamic enabled policies. Maximum rate percentage is the maximum percentage of maximum user rate of dynamically enabled policy.

Remove categories of the specified Bandwidth Controller policy.

Remove all categories of the specified Bandwidth Controller policy.

Sets the Bandwidth Controller policy categories with the specified specified maximum rates. Maximum rate is the maximum bandwidth allowed for all the flows going through this policy category. Maximum rates cannot exceed the maximum user rate of the parent Bandwidth Controller policy.

Gets the maximum rates of the Bandwidth Controller policy categories.

Sets a set of Bandwidth Controller policy categories with specified rate percentages. Rate percentages is maximum percentage of the maximum user rate allowed for all the flows going through this Bandwidth Controller policy category.

Gets the maximum percentages of Bandwidth Controller policy categories.

Sets the IP-TOS value for the specified Bandwidth Controller Category. If set then all non-conforming Layer 3 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth category. A value of 255 means it's a pass through and all the Layer 3 packets are passed as seen by the Bandwidth Controller.

Gets the IP-TOS value for specified Bandwidth Controller category.

Sets the Link-QOS for the specified Bandwidth Controller categories. All non-conforming Layer 2 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth category. A value of 255 means it's a pass through and all the Layer 2 packets are passed as seen by the Bandwidth Controller.

Gets the Link-QOS for the specified Bandwidth Controller categories.

Enables/disables the measurement of bandwidth for Bandwidth Controller policies.

Gets the currently configured enabled/disabled setting for the bandwidth measurement feature for the specified Bandwidth Controller policies. For more information about log publishers see Log::Publisher.

Specify a destination log publisher for the bandwidth measurement logs to be sent.

Returns previously configured log publisher setting for the measurement feature.

Specify the time interval with which bandwidth measurement log messages are sent to log server. Specified in milliseconds.

Gets the previously configured log period setting of the Bandwidth Controller policies.

Gets the version information for this interface.

Gets the names of all Bandwidth Controller policies.

Creates a set of Bandwidth Controller policies.

Deletes a set of Bandwidth Controller policies.

Deletes all Bandwidth Controller policies.

Sets the descriptions for the specified Bandwidth Controller policies. This is an arbitrary field which can be used for any purpose.

Gets the descriptions for the specified Bandwidth Controller policies.

Gets the dynamic states of the specified Bandwidth Controller policies.

Sets the IP-TOS value for the specified Bandwidth Controller policies. If set then all non-conforming Layer 3 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth policy. A value of 255 means it's a pass through and all the Layer 3 packets are passed as seen by the Bandwidth Controller.

Gets the IP-TOS value for the specified Bandwidth Controller policies.

Sets the Link-QOS for the specified Bandwidth Controller policies. All non-conforming Layer 2 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth policy. A value of 255 means it's a pass through and all the Layer 2 packets are passed as seen by the Bandwidth Controller.

Gets the Link-QOS for the specified Bandwidth Controller policies.

Sets the maximum rate for the specified Bandwidth Controller policies. Maximum rates is maximum bandwidth allowed for all the flows going going through this policy. Maximum rates value should be between 1000000bps and 320000000000 bps.

Gets the maximum rate for the specified Bandwidth Controller policies.

Sets the maximum user rate in packets per second (PPS) for the specified Bandwidth Controller policies. The maximum user rate is the maximum bandwidth allowed for all the flows going through this dynamically created instance of the Bandwidth Controller policy. The maximum user rate cannot be higher than the maximum rate specified for that Bandwidth Controller policy.

Gets the maximum user rate in packets per second (PPS) for the specified Bandwidth Controller policies.

Sets the maximum user rate for the specified Bandwidth Controller policies. Maximum user rates is maximum bandwidth allowed for all the flows going through this dynamically created instance of the Bandwidth Controller policy. Maximum user rate value should be between 5000 bps and 2000000000 bps. Maximum user rate cannot be higher than maximum rate specified for that Bandwidth Controller policy.

Gets the maximum user rate for the specified Bandwidth Controller policies.

Gets the names of all Bandwidth Controller policy categories. Categories is a sub-policy of dynamically created instances from a dynamic enabled policy.

Creates a set of Bandwidth Controller policy categories with the specified maximum rates. Categories is a sub-policy of dynamically created instances from a dynamic enabled policies. Maximum rates cannot exceed the maximum user rate of the parent Bandwidth Controller policy.

Creates a set of Bandwidth Controller policy categories with the specified maximum rate percentages. Categories is a sub-policy of dynamically created instances from a dynamic enabled policies. Maximum rate percentage is the maximum percentage of maximum user rate of dynamically enabled policy.

Remove categories of the specified Bandwidth Controller policy.

Remove all categories of the specified Bandwidth Controller policy.

Sets the Bandwidth Controller policy categories with the specified specified maximum rates. Maximum rate is the maximum bandwidth allowed for all the flows going through this policy category. Maximum rates cannot exceed the maximum user rate of the parent Bandwidth Controller policy.

Gets the maximum rates of the Bandwidth Controller policy categories.

Sets a set of Bandwidth Controller policy categories with specified rate percentages. Rate percentages is maximum percentage of the maximum user rate allowed for all the flows going through this Bandwidth Controller policy category.

Gets the maximum percentages of Bandwidth Controller policy categories.

Sets the IP-TOS value for the specified Bandwidth Controller Category. If set then all non-conforming Layer 3 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth category. A value of 255 means it's a pass through and all the Layer 3 packets are passed as seen by the Bandwidth Controller.

Gets the IP-TOS value for specified Bandwidth Controller category.

Sets the Link-QOS for the specified Bandwidth Controller categories. All non-conforming Layer 2 packets are set with this value. A non-conforming packet is one which exceeds the rate limit of the configured Bandwidth category. A value of 255 means it's a pass through and all the Layer 2 packets are passed as seen by the Bandwidth Controller.

Gets the Link-QOS for the specified Bandwidth Controller categories.

Enables/disables the measurement of bandwidth for Bandwidth Controller policies.

Gets the currently configured enabled/disabled setting for the bandwidth measurement feature for the specified Bandwidth Controller policies. For more information about log publishers see Log::Publisher.

Specify a destination log publisher for the bandwidth measurement logs to be sent.

Returns previously configured log publisher setting for the measurement feature.

Specify the time interval with which bandwidth measurement log messages are sent to log server. Specified in milliseconds.

Gets the previously configured log period setting of the Bandwidth Controller policies.

Gets the version information for this interface.

This interface configures the Bandwidth Controller policy components to manage the egress bandwidth per policy, per session or subscriber, per application and various combinations of these.